Airsoft accumulator / battery Li-Ion HellArms 3S 11,1V / 2800mAh 35/85A - Selecting a connector: T-Dean

More photos (8)

Add to favourites Add to compare list

Airsoft accumulator / battery Li-Ion HellArms 3S 11,1V / 2800mAh 35/85A - Selecting a connector: T-Dean

Powerful airsoft Li-Ion battery with nominal voltage 11,1V, capacity 2800mAh with discharge currents 35A permanently and 85A short-term. The connector can be selected XT60 or T-Dean. More

Product code: HA283A-T-DEAN Shipping and Payment

43,50 EUR incl. VAT

Powerful airsoft Li-Ion battery with nominal voltage 11,1V, capacity 2800mAh with discharge currents 35A permanently and 85A short-term. The connector can be selected XT60 or T-Dean. More

Product code: HA283A-T-DEAN Shipping and Payment

Airsoft Li-Ion accumulator / battery of our own production consists of three cells in a steel casing. The battery has a voltage of 11.1V, a capacity of 2800mAh and can handle long term discharge currents of 35A and short term 85A. We have tested these values both in laboratory conditions and in practice.

Thanks to the steel casing, there is no inflation as with Li-Pol batteries. Due to its size and capacity it is more suitable for airsoft use. The battery is able to operate in temperatures from -40 to 60 °C. The battery has a large capacity for its small size. After 500 cycles, the battery has 90% of its original capacity. This means that if you go out to play on average 8 months of the year every Saturday and take proper care of the Li-Ion battery, your total capacity will drop by 10% in 14 years.

Parameters	Discharge current: long term 35A, short term 85A Total battery voltage is 11.1V Voltage per cell: nominal 3.6V, charged 4.2V, discharged 2.5V
Capacity	Battery capacity 2800mAh. On one charge, depending on the configuration of the weapon, you will shoot approximately 2100 rounds.
Dimensions	Overall dimensions of the accumulator Ø 19 mm (cylinder) x 206 mm (length). See product photo with dimensions.
Charging	Charging current: recommended 2.8A, maximum 6A Charging time: at recommended current 1.5 hours
Temperature	Charging 0°C to 60°C When discharging -40°C to 60°C
Other	You can choose XT60 or T-Dean connector.

Application Li-Ion 2800mAh 11.1V

This smaller battery fits under the cover of most AKs. Due to its medium hardness it is not suitable for extremely powerful assemblies. An example of a recommended maximum load is the assembly:

Our recommended assemblies for this battery:

Gears	12:1	13:1	16:1	18:1	100:200	100:300
Motor HellArms	Unsuitable due to high cadence	Unsuitable due to high cadence	Up to M130 - 33 RPS	Unsuitable due to wheel geometry	Up to M150 - 24 RPS	Up to M170 - 21 RPS
Motor ASG, SHS 30K	Up to M130 - 32 RPS	Up to M130 - 30 RPS	Up to M140 - 24 RPS	Up to M150 - 21 RPS	Up to M160 - 17 RPS	Up to M170 - 15 RPS
Basic motor	Up to M120	Up to M120	Up to M130	Up to M130	Up to M140	Up to M150

*The neodymium magnet load motors (Guarder, ASG, SHS) will have better response and higher cadence than the basic ones. The HellArms motor will have a higher cadence and lower response than the motors previously mentioned. High speed motors combined with lower gearing than 100:200 and this battery are not recommended at all.

*The springs in the table above are Guarder and ASG Ultimate, which are the only springs we recommend using due to their characteristics, durability, performance stability, and their minimal manufacturing differences in stiffness.

Find out how to care for this battery in the article below

Why buy a battery from us?

We carefully select the most suitable cells on the market that meet our requirements for airsoft use. We take great care with every battery we produce and test it at the end of production. The batteries do not deform, they have durable hand soldered joints that are individually stripped. The individual cells are connected by a wide copper strip with a cross section of 2.5 mm for the best possible electrical and thermal conductivity. The main wiring is made of the highest quality 1.5 mm diameter silicone wires on the market. The connector can be either XT60 (which we recommend) or T-Dean.